The Leuze AC-AN-A (Part No. 63000701) is a precision-engineered actuator designed for normal-duty applications where reliability, compact size, and stainless steel construction are essential. This angled actuator is ideal for integration into a wide range of industrial automation setups.
| Parameter | Details |
|---|---|
| Part Number | 63000701 |
| Model Name | AC-AN-A |
| Dimensions (W × H × L) | 28 mm × 11.8 mm × 30.7 mm |
| Net Weight | 10 g |
| Mounting Type | Through-hole mounting |
| Mounting Bore Holes | In key direction |
| Actuator Design | Angled |
| Application | Normal duty |
| Material | Stainless steel |
| Classification Standard | Code |
|---|---|
| Customs Tariff Number | 85369095 |
| ECLASS 5.1.4 / 8.0 | 27279216 |
| ECLASS 9.0 to 15.0 | 27272606 |
| ETIM 5.0 to 10.0 | EC001487 |
All dimensions in millimeters (mm):
Key Dimensions: 2, 4, 6.7, 9, 10.5, 14.5, 15, 21, 28
Radius: R 220
Bore Diameter: Ø4.5 mm
Clearances: ≥ (minimum clearances shown in technical diagram)
Compact design for space-constrained installations
Angled actuator for better reach and actuation geometry
Durable stainless steel construction for corrosion resistance
Lightweight (only 10 g) – reduces load on mounting surfaces
Normal duty rated for general industrial usage
Standardized mounting with through-hole and key-alignment
International classification codes for ease in inventory and compliance
Supports digital twin systems through ETIM/ECLASS entries
High precision with tightly specified dimensions
Manufactured by Leuze, a trusted industrial automation brand
| Issue | Possible Cause | Suggested Solution |
|---|---|---|
| 1. Actuator does not move | Misalignment | Verify proper installation per drawing |
| 2. Mounting holes do not fit | Wrong key direction | Realign according to key slot spec |
| 3. Loose mounting | Under-tightened screws | Check torque settings |
| 4. Rust or corrosion | Improper environment | Use only in specified normal-duty conditions |
| 5. Breakage | Excessive mechanical load | Verify force limits |
| 6. Vibrating actuator | Weak fastening | Re-tighten mounting |
| 7. Incorrect bore size | Wrong part ordered | Confirm Ø4.5 mm bore match |
| 8. Sensor not triggered | Misplaced actuator | Realign actuator angle/distance |
| 9. Missing signals | Wiring error in system | Inspect electrical setup |
| 10. Deformation | Heat exposure | Avoid excessive ambient temperatures |
| 11. Scratches or dents | Rough handling | Improve transport/storage care |
| 12. Wear marks | Continuous overuse | Inspect cycle count vs. rated life |
| 13. Actuator stuck | Foreign debris | Clean mounting area |
| 14. Assembly mismatch | Wrong actuator type | Confirm part number: 63000701 |
| 15. No documentation | Missing label | Refer manufacturer site (www.leuze.com) |
| 16. Delay in movement | Mechanical friction | Lubricate or clean mount contact |
| 17. Over-tightened screws | Thread damage | Use torque wrench |
| 18. Stainless steel discoloration | Chemical exposure | Use protective environment |
| 19. Interference with other parts | Crowded setup | Ensure spacing per dimensioned drawing |
| 20. Product not recognized in ERP | Missing classification | Use ECLASS & ETIM codes correctly |
| 21. Frequent replacements | Wrong duty class | Use actuator only for normal duty |
| 22. Sensor signal drops | Loose sensor-actuator gap | Adjust distance/alignment |
| 23. Assembly confusion | Similar parts mixed | Label all actuators during storage |
| 24. Cannot access mounting holes | Obstructed access | Redesign fixture if needed |
| 25. Vibration noise | Poor base mounting | Add damping material |
| 26. Premature wear | Non-aligned actuator path | Check for skewed movement |
| 27. Part bends on use | Excessive torque | Validate movement mechanics |
| 28. Surface pitting | Moisture ingress | Ensure dry working condition |
| 29. Sticking after long rest | Surface corrosion | Operate periodically to avoid rust |
| 30. Procurement mismatch | Wrong code used | Double-check: ECLASS 27272606 / ETIM EC001487 |